Instructions

Important

Surfaces

Frequently Asked Questions

• If I am on tank water, can I use Wet & Forget on my roof?

  You sure can, however you must disconnect the water supply to your tank for at least 10mm of rain or 2 good downpours to remove the concentrate. Wet & Forget has been used for over 25 years to treat biological growth on roofs.

• How much Wet & Forget will I need to clean my roof?

  The average 3 bedroom tile roof is approx 150 sq metres, because of the undulations of the tile profile the actual area is a lot bigger. Therefore an average tile/concrete roof would require 2 x 5 litre bottles, depending on how porous the surface is and how much biological growth is present. For an average 3 bedroom tile roof with lichen you would require 3 x 5 litre bottles depending on the total area covered with lichen. For best results mix the Wet & Forget and spot spray the lichen, leave for 15 minutes and then respray the lichen and the entire roof to ensure the lichen absorbs the Wet & Forget thoroughly. The first application is to dissolve the waxy surface and the 2nd spray will then penetrate the lichen. For green moss and black mould one application is normally sufficient. Your roof will normally take between 6-12 months to come clean.

• Will Wet & Forget affect my pets?

  Keep your animals off the treated surface until the product is dry to ensure that they don’t lick any of the product. If they accidentally walk or sit in the product before it dries, wash the affected areas with fresh water as a precaution.

• Will Wet & Forget damage my plants?

  Wet & Forget is okay to use around plants provided certain protective steps are taken. When spraying the product near plants, make sure to either cover them with a tarpaulin (or something similar) or alternatively, wash the plants down with water before and after applying the product nearby. The leaves of the plant may experience a slight discolouration or spot burn if they come into contact with the product for an extended period.

• Can I change the specified ratios given in the instructions for Wet & Forget?

  Yes. If the contamination is extreme, increase the strength or apply a second application a month after the first. However, if you have cleaned the surface previously with Wet & Forget and you want to give it just a maintenance spray, you can decrease the strength if the contamination is light. The cleaning process will still be just as effective.

• Do I have to apply Wet & Forget all at once?

  You don't have to spray the entire area at once, just remember where you have stopped and started. The product is fine if left in the spray container as it does not deteriorate when it has been diluted. It will not damage your garden sprayer as it is not corrosive.

• How often do I need to apply Wet & Forget?

  After the initial application, Wet & Forget only needs to be used for maintenance. Apply at the first sign of regrowth to avoid the need for a large scale application.

• What is the shelf life of Wet & Forget?

  Wet & Forget has an unlimited shelf life. Always keep the cap done up tightly and the container out of reach of children.

• What is the dilution rate and coverage of Wet & Forget?

  Dilute Wet & Forget 1:5 (1 part Wet & Forget to 5 parts water). Every 5L bottle makes 30L of product to spray. The coverage is between 100-300 sq metres depending on the porosity of the surface and the level of contamination, i.e. painted surfaces will use less product but porous surfaces readily absorb the product and therefore coverage could be in the range of 100-150 sq metres.

• Can I use Wet & Forget around my pool?

  Yes it is fine to use on your pool surrounds. It is best applied in the coolest part of the day when the surface is dry. If you accidently get run off into the pool it won't alter the pool water balance.

• Will Wet & Forget remove the mould off my timber deck?

  Most definitely! However if your deck is older and has never been cleaned, it may be noticeably blackened with the contamination. In this case, we recommend to wait a month after the application and give the area a light brush with a broom or scrubbing brush with warm water to help remove the dead growth. The good news is that you should only have to do this once and then the maintenance is easy.

• Will Wet & Forget get moss out of lawns?

  Sure will! Firstly, lightly water the lawn but not enough to saturate the moss. Do this late in the day when the sun is low so that evaporation is kept to a minimum. Dilute the Wet & Forget 1:7 (1 part Wet & Forget to 7 parts water) and spot spray the moss. You may have to give it a couple of goes until you have it under control. At worst you may get slight burning on the grass but it will recover very quickly. Rake the dead moss out, then sprinkle lime over the area as this is usually a sign that your pH of the soil is not quite right.

• If I have just applied Wet & Forget, am I able to paint or seal the area?

  You must wait until all the mould has decomposed before you can paint or seal the area.

Testimonials